Search for Products
P.O. Box 17062 CLEARWATER, FL 33762
PH. 1-727-789-5786 FAX 1-727-572-9926
PH. 1-727-789-5786 FAX 1-727-572-9926
www.floridawaterblast.net
PetroXtractor®
Advantages
Applications
Features
PetroXtractor Underground Systems
Non-XP, Vapor-Tight
This unit features:
The PetroXtractor is a dependable and cost effective means of
removing oil, fuel, and other floating hydrocarbons from water
where access to the fluid surface is limited. It provides efficient
remediation of groundwater contaminated by oil, using existing re-
covery and monitoring wells. Often, the PetroXtractor working
alone will reduce oil or fuel content to an acceptable E.P.A. level.
Models are available for two inch, four inch, and six inch or larger
ID well casings, with removal rates up to 12 gph. (based on SEA
30 motor oil). Depths of 100 feet or more can be accommodated
without the use of pumps.
removing oil, fuel, and other floating hydrocarbons from water
where access to the fluid surface is limited. It provides efficient
remediation of groundwater contaminated by oil, using existing re-
covery and monitoring wells. Often, the PetroXtractor working
alone will reduce oil or fuel content to an acceptable E.P.A. level.
Models are available for two inch, four inch, and six inch or larger
ID well casings, with removal rates up to 12 gph. (based on SEA
30 motor oil). Depths of 100 feet or more can be accommodated
without the use of pumps.
Oil Skimming for Wells and Other Small
Openings with Large Vertical Drops
Openings with Large Vertical Drops
The PetroXtractor is an oil skimmer that makes use of the differ-
ences in specific gravity and surface tension between oil and
water. These physical characteristics allow the unit's continuous
belt to attract floating oil in the well. After picking up the oil, the belt
travels over the head pulley on the drive unit and through tandem
wiper blades. The oil is then scraped off both sides of the belt and
discharged through a 1 - 1/4" ID hose. The unique bearing less de-
sign of the tail pulley (immersed in the well water) with its tethered
frame allows it to perform three important functions: it keeps pro-
per tension on the belt, prevents accidental loss down the well,
and keeps the belt centered in the casing.
ences in specific gravity and surface tension between oil and
water. These physical characteristics allow the unit's continuous
belt to attract floating oil in the well. After picking up the oil, the belt
travels over the head pulley on the drive unit and through tandem
wiper blades. The oil is then scraped off both sides of the belt and
discharged through a 1 - 1/4" ID hose. The unique bearing less de-
sign of the tail pulley (immersed in the well water) with its tethered
frame allows it to perform three important functions: it keeps pro-
per tension on the belt, prevents accidental loss down the well,
and keeps the belt centered in the casing.
The PetroXtractor can be installed in existing wells by mounting it on a flat surface above the well casing.
Skimmer operation consists of merely lowering the belt and tail pulley into the casing until the pulley is fully
immersed, placing the discharge hose in a container, and switching the unit on.
Skimmer operation consists of merely lowering the belt and tail pulley into the casing until the pulley is fully
immersed, placing the discharge hose in a container, and switching the unit on.
Explosion Proof
This unit features:
This unit features:
Solar Powered PetroXtractor
Vacuum Assisted Skimming
The latest system!
Rugged Construction For Harsh Conditions: The PetroXtractor will provide for many years of
trouble-free service. Belts are specifically selected for your application ( see Belt Selection page ).
A tough power train keeps the PetroXtractor running under the most severe conditions. With the
proper configuration, the PetroXtractor can handle liquid temperatures up to 180 °F, and the pH of
the fluid can range from 1 to 13.
trouble-free service. Belts are specifically selected for your application ( see Belt Selection page ).
A tough power train keeps the PetroXtractor running under the most severe conditions. With the
proper configuration, the PetroXtractor can handle liquid temperatures up to 180 °F, and the pH of
the fluid can range from 1 to 13.
The PetroXtractor is designed for those applications that have a limited access area and a deep drop be-
tween the mounting surface and the surface of the liquid. The unit can be used anywhere,even where
no electric power or compressed air is available. Explosion proof and pneumatic motors are available for
areas where combustible fumes may be present. Vapor-tight models can also enhance the explosion
proof properties of the unit.
tween the mounting surface and the surface of the liquid. The unit can be used anywhere,even where
no electric power or compressed air is available. Explosion proof and pneumatic motors are available for
areas where combustible fumes may be present. Vapor-tight models can also enhance the explosion
proof properties of the unit.
All units can be built Explosion Proof, Vapor-Tight or Standard. Size of transfer
pump is dependent on product, run to AST and grade differential.
pump is dependent on product, run to AST and grade differential.
Standard
This unit is presently being tested on "Naval Special
Fuel" at Pearl Harbor, HI, by Tetra Tech, Inc. Prelim-
inary results are due sometime in September. It fea-
tures a 60 gal tank and fully automated controls.
Fuel" at Pearl Harbor, HI, by Tetra Tech, Inc. Prelim-
inary results are due sometime in September. It fea-
tures a 60 gal tank and fully automated controls.
Now you can remediate where there is no power!
Specifications
Oil Removal Rate:
Model PX-A: 3 gph (11 lph) with 1 in.(2.5 cm) wide belt
Model PX-B: 6 gph (23 lph) with 2 in.(5 cm) wide belt
Model PX-C:12 gph (45 lph) with 4 in.(10 cm) wide belt
(Removal rate is based on 30 weight oil in water.)
Model PX-A: 3 gph (11 lph) with 1 in.(2.5 cm) wide belt
Model PX-B: 6 gph (23 lph) with 2 in.(5 cm) wide belt
Model PX-C:12 gph (45 lph) with 4 in.(10 cm) wide belt
(Removal rate is based on 30 weight oil in water.)
Motor: Fractional hp TEFC, 115VAC, single phase, 60 Hz gear
motor, including 8 foot cord with electrical plug
Optional: 50 Hz; 3-phase; explosion proof; 12VDC;
and pneumatic
motor, including 8 foot cord with electrical plug
Optional: 50 Hz; 3-phase; explosion proof; 12VDC;
and pneumatic
Belt Width (Specify):
PX-A (1 in. (2.5 cm) for 2 in. (5 cm) ID casing
PX-B (2 in. (5 cm)) for 4 in. (10 cm) ID casing
PX-C (4 in. (10 cm)) for 6 in. (15 cm) ID casing
PX-A (1 in. (2.5 cm) for 2 in. (5 cm) ID casing
PX-B (2 in. (5 cm)) for 4 in. (10 cm) ID casing
PX-C (4 in. (10 cm)) for 6 in. (15 cm) ID casing
Belt Length: User specified (up to 100', measured from the
center of head pulley to center of tail pulley)
center of head pulley to center of tail pulley)
Wiper Material: UHC rubber standard, Optional: Nitrile, CRV rubber and Ceramic
Mounting Method: Flat base mount with oil discharge through a
1-1/4 in. (3.1cm) ID hose
1-1/4 in. (3.1cm) ID hose
Mounting Area: Installation drawing coming soon.
Weights: Complete assembly without tail pulley or belt:
Model PX-A: 30 lbs. (13.6 Kg.)
Model PX-B: 31 lbs. (14 Kg.)
Model PX-C: 38 lbs. (17 Kg.)
Model PX-A: 30 lbs. (13.6 Kg.)
Model PX-B: 31 lbs. (14 Kg.)
Model PX-C: 38 lbs. (17 Kg.)
PX-A Tail pulley: 2 lbs. ( 1.3 Kg.)
PX-B Tail Pulley: 3 lbs. ( 2.7 Kg.)
PX-C Tail Pulley: 4.5 lbs. (4.1 Kg.)
PX-B Tail Pulley: 3 lbs. ( 2.7 Kg.)
PX-C Tail Pulley: 4.5 lbs. (4.1 Kg.)
PX-A, 1 in. x 5 ft (1.5m) polymer belt: 0.55 lbs.(0.25 Kg.)
PX-B, 2 in. x 5 ft (1.5m) polymer belt: 1.1 lbs. (0.5 Kg.)
PX-C, 4 in. x 5 ft (1.5m) polymer belt: 2.2 lbs. (1.0 Kg.)
(Belt weight varies according to actual length specified.)
PX-B, 2 in. x 5 ft (1.5m) polymer belt: 1.1 lbs. (0.5 Kg.)
PX-C, 4 in. x 5 ft (1.5m) polymer belt: 2.2 lbs. (1.0 Kg.)
(Belt weight varies according to actual length specified.)
Standard Configuration: The Abanaki PetroXtractor is supplied with a head pulley guard,
adjustable wiper blade assembly, skimmer belt, tail pulley, fractional hp, 110VAC, 60 Hz
gear motor, and assembly/maintence instructions.
adjustable wiper blade assembly, skimmer belt, tail pulley, fractional hp, 110VAC, 60 Hz
gear motor, and assembly/maintence instructions.
Specification Notes:
FLORIDA WATER BLAST, INC. Clearwater Florida Ph. 1-727-789-5786
WATER TREATMENT SYSTEMS
Industrial Oil Skimmers
oil skimmers, oil skimmer, grease skimmer, belt oil skimmer, coolant odor, groundwater sump, skimmer, belt oil
skimmers, groundwater remediation, oil water separator, oilskimmers, skimmers, wastewater, oil skimmer,
well product skimmers, 18" disc oil skimmers, 2" belt skimmers(no. 6 fuel oil), abanaki oil skimmer, belt skimmer
4 inch monitoring wells, best uses for oil skimmers, LNAPL recovery, DNAPL recovery, oil removal, tramp oil,
waste oil, skimmer pump, oil grabber, mighty mini, pollution control, Abanaki, oil water separator, belt skimmer,
oil skimming, belt skimmers, coolant smell, remediation equipment, wastewater, oil removal, air vacuum,
vacuum, sump cleaning, industrial vacuum, vacuum, coolant removal, wet vacuum, wet vac, pneumatic
vacuum, pneumatic drum vacuum, coolant maintenance, q-vac, qvac, Q-vac, Qvac100, q-vac 100, shop
vacuum, liquid vacuum, oil vacuum, coolant vacuum, Metalworking fluid, metalworking shops, coolant,
lubricant, cutting fluid, skimmer, maintenance, products, equipment, oil skimmers, oil removal, sump,
coalescers, Zebra Skimmers, abanaki, florida water blast, inc.